StrongArm 4523L Mitsubishi 3000GT Hood Lift Support (L) 1991-99, Pack of 1,black and chrome

[]

Retail Price: $ 28.45

Wholesale Price: Inquire Now

hood strut; lift support; lift strut; trunk support; lift shock

trunk, hatch and hood supports, trunk lift, hatch lift, hood lift, lift support

How Lift Supports Work?

Gas-charged lift supports are energy storage devices which create energy by compressing gas inside a cylinder. When closed, the energy is stored. When opened, the energy is released to raise hoods, trunks, hatches and hold them safely in an open position.

StrongArm gas-charged lift supports typically store a gas charge of over 1500psi and cannot be compressed by hand. For safe and effective operation, the lift supports must match the specific application.

Why Replace Your Lift Supports?

Opening your vehicle’s hatch or checking under the hood should not be a serious safety hazard for you and your family.

Just like tire wear, your hood lifts and struts will lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. Smart drivers and mechanics periodically check the function of all vehicle lift support parts especially if the vehicle is five years or older.

Here's the best part - StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.

Original lift supports
Easy, quick installation
No special tools required
OEM design and performance

What's inside lift support, lift support cross section, gas charged lift support

StrongArm Lift Supports Installation Guide

Easy, Step-by-Step Instructions

Have someone hold the hatch, hood, trunk or rear window open while replacing the lift support. Do not use a prop rod.

Turn off ignition. If old lift support has a window defogger electrical connector, carefully disconnect the fittings.
Before removing old lift supports, examine any hardware provided to determine which components must be reused.
Work on lift supports one at a time and do not remove both lift supports at the same time. Replace one, then remove and replace the second one.
The new lift support must be installed in the same position as the old one which was removed, unless otherwise instructed. Do not nick or scratch chrome rod.
Compare the end connectors of your lift support to the illustrations provided and see additional instructions below.

Things to keep in mind:

Always replace both lift supports when applicable to assure top performance
Carefully inspect all hinges and connecting points and replace if broken, old or fractured
Do not use a prop rod and have someone help you


Removable Ball Connectors If your lift supports come with the ball connectors, remove old lift support by prying the retaining ring, cap lock or the security lock ring. Then press new lift support onto ball stud and properly install retainer.	Eyelet Connector If your lift supports come with the eyelet connector, remove old lift support by unscrewing the mounting bolt or retaining clip. Install new lift support by using mounting bold or removing the retaining clip. Then, remove old lift support by prying the retaining clip off. Install new lift support by pressing against the vehicle mounting stud until the retaining clip snaps into place.	Eyelet Connector with Retaining Clip If your lift supports come with the eyelet connector with retaining clip, remove old lift support by prying the retaining clip off. Then, install new lift support by pressing against the vehicle mounting stud until the retaining clip snaps into place.	Keyhole Slot Connector If your lift supports come with the keyhole slot connector, slide the lift support so the keyhole slot can be lifted off the vehicle mounting stud. Then install the new lift support by sliding the keyhole slot over the vehicle mounting stud.

This website follows the safe harbor principle. If any infringement, please inform us in time and we will delete it in time. About safe harbor，please click here to learn more.

After Sale Service:

1 Insurance Policy: Click to go to the Help Center to view the Insurance Policy

2 The rules apply and summit for receive compensation

3 The conditions of accrual for amount insurance

5 Damage to the parcel during international shipping, which resulted in damage to the goods in it

6 Loss of individual goods under international shipment The absence individual goods in the parcel

7 Non-compliance individual goods in color, size, complications Damage to the goods during international shipment

8 Returns Policy: Click to go to the Help Center to view the Returns Policy

All Category
All Category

Women's Clothings

Men's Clothings

StrongArm 4523L Mitsubishi 3000GT Hood Lift Support (L) 1991-99, Pack of 1,black and chrome

BEST SELLERS

Product introduction

Shipping Notices

StrongArm gas charged lift supports are custom engineered and manufactured beyond industry standards to provide smooth operation and durability. The hardened chromium plated steel shaft is precision ground and polished for superior corrosion resistance and leak free sealing. The self cleaning piston assembly automatically opens during each compression cycle to keep the orifice clear of fluid contaminants and provide smoother operation and reliable performance. Most units also utilize StrongArm's patented temperature compensation module valve which ensures consistent operation even in extreme weather conditions. It does so by compensating for normal gas pressure changes caused by temperature variations. The metallic upper bushing is manufactured with bearing quality precision to provide exact fit with pistion rod and promote a long operating life.

From the manufacturer

How Lift Supports Work?

Why Replace Your Lift Supports?

Opening your vehicle’s hatch or checking under the hood should not be a serious safety hazard for you and your family.

Here's the best part - StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.

Original lift supports
Easy, quick installation
No special tools required
OEM design and performance

StrongArm Lift Supports Installation Guide

Easy, Step-by-Step Instructions

Have someone hold the hatch, hood, trunk or rear window open while replacing the lift support. Do not use a prop rod.

Turn off ignition. If old lift support has a window defogger electrical connector, carefully disconnect the fittings.
Before removing old lift supports, examine any hardware provided to determine which components must be reused.
Work on lift supports one at a time and do not remove both lift supports at the same time. Replace one, then remove and replace the second one.
The new lift support must be installed in the same position as the old one which was removed, unless otherwise instructed. Do not nick or scratch chrome rod.
Compare the end connectors of your lift support to the illustrations provided and see additional instructions below.

Things to keep in mind:

Always replace both lift supports when applicable to assure top performance
Carefully inspect all hinges and connecting points and replace if broken, old or fractured
Do not use a prop rod and have someone help you


Removable Ball Connectors If your lift supports come with the ball connectors, remove old lift support by prying the retaining ring, cap lock or the security lock ring. Then press new lift support onto ball stud and properly install retainer.	Eyelet Connector If your lift supports come with the eyelet connector, remove old lift support by unscrewing the mounting bolt or retaining clip. Install new lift support by using mounting bold or removing the retaining clip. Then, remove old lift support by prying the retaining clip off. Install new lift support by pressing against the vehicle mounting stud until the retaining clip snaps into place.	Eyelet Connector with Retaining Clip If your lift supports come with the eyelet connector with retaining clip, remove old lift support by prying the retaining clip off. Then, install new lift support by pressing against the vehicle mounting stud until the retaining clip snaps into place.	Keyhole Slot Connector If your lift supports come with the keyhole slot connector, slide the lift support so the keyhole slot can be lifted off the vehicle mounting stud. Then install the new lift support by sliding the keyhole slot over the vehicle mounting stud.

Shipping Notices:

1 Contraband and limited items:

Clgarette,Alcohol,Contraband ?Do not accept

Liquid,cream or cosmetics items are quantity limited in shopping agent service

Chinese medicine is limited to ship by Chinese exporting goods.

2 Limitation for different shipping methods:

3 Yoybuy Product's Label:

Sensitive Product(SEN)

Product With battery

Cream

Powder

Dangerous Products

4 Volume weight Requested:

volume weight=length*height*Width/5000

one side must be less than 120cm，otherwise there is additional fee；250cm products can not be accept；

Any side must be less than 60cm，otherwise you will be charged the greater one between real weight and volume weight，more than 120cm will be not accepted.