- ✅ 12-gauge carbon steel (almost 1/8\" thick) - zinc coated to prevent rusting and corrosion
- ✅ Countersunk holes on opposite sides to keep screw heads flush, designed for #6 flat head screws
- ✅ Dimension: each fastener measures 1-3/16\" x 5/8\" x 12\"gauge (almost 1/8\" thick)
- ✅ Widely Use: Hardware, Table tops, desk tops, cabinet fronts, drawer fronts etc.
- ✅ Easy to install and inexpensive: The shape of the figure 8 fastener allows them to pivot as the tabletop expands and contracts. These fasteners can be installed on the inside or outside of the apron.
About our fighure 8 fasteners
Our figure-8 fasteners are an ideal way of attaching wooden tops to your desks and tables, while also allowing for seasonal expansion and contraction of the wood. These fasteners are made of heavy gauge steel, nearly an 1/8'' thick. Thanks to their flat bearing surfaces and circular ends, the figure-eight clips can easily pivot in their recesses when the top moves, which helps to prevent splitting. To allow for more wood movement on larger tops, they are best used in end aprons only. Each desktop fastener is countersunk for screw heads in opposing directions.
How to install
MARK THE POSITION
After building the base, decide where you want to position your table top fasteners. They should be evenly spaced around the perimeter of the base.
Place half of the figure 8 fastener on the top of the base with the center of the 8 on the edge. Typically you want this on the inside of the frame so the fastener won’t be seen. Trace around the end with a pencil to mark the position.
DRILL A SHALLOW HOLE WITH A FORSTNER BIT
A Forstner bit creates a clean, flat-bottomed hole, and is perfect for drilling a shallow hole that will allow the figure 8 fastener to sit flush with the top of the base.
Check to make sure the bit is the same diameter as the side you traced earlier. I’m using a 5/8″ bit for the smaller side of the 8. The larger side is 3/4″ if you choose to use that one instead.
Wood movement problem
Believe it or not, wood can soak up the humidity in the air like a sponge and swell in high humidity! If you’ve ever notice a door in your home sticking during the summer, but works fine in the winter, you’ve seen wood movement in action.The problem with wood movement isn’t that the boards gets longer. They get wider as those cells soak up the moisture in the air. There are two common assembly problems that can cause your project to fail.
High quality
It is made with the high quality of die casting steel (almost 1/8" thick) coated with zinc for rusting and corrosion resistance. Each fastener measures 1-3/16" x 5/8" x 12 gauge (~1/8") thick.
BEST SELLERS
Product Description
About our fighure 8 fasteners
Our figure-8 fasteners are an ideal way of attaching wooden tops to your desks and tables, while also allowing for seasonal expansion and contraction of the wood. These fasteners are made of heavy gauge steel, nearly an 1/8'' thick. Thanks to their flat bearing surfaces and circular ends, the figure-eight clips can easily pivot in their recesses when the top moves, which helps to prevent splitting. To allow for more wood movement on larger tops, they are best used in end aprons only. Each desktop fastener is countersunk for screw heads in opposing directions.
How to install
MARK THE POSITION
After building the base, decide where you want to position your table top fasteners. They should be evenly spaced around the perimeter of the base.
Place half of the figure 8 fastener on the top of the base with the center of the 8 on the edge. Typically you want this on the inside of the frame so the fastener won’t be seen. Trace around the end with a pencil to mark the position.
DRILL A SHALLOW HOLE WITH A FORSTNER BIT
A Forstner bit creates a clean, flat-bottomed hole, and is perfect for drilling a shallow hole that will allow the figure 8 fastener to sit flush with the top of the base.
Check to make sure the bit is the same diameter as the side you traced earlier. I’m using a 5/8″ bit for the smaller side of the 8. The larger side is 3/4″ if you choose to use that one instead.
Wood movement problem
Believe it or not, wood can soak up the humidity in the air like a sponge and swell in high humidity! If you’ve ever notice a door in your home sticking during the summer, but works fine in the winter, you’ve seen wood movement in action.The problem with wood movement isn’t that the boards gets longer. They get wider as those cells soak up the moisture in the air. There are two common assembly problems that can cause your project to fail.
High quality
It is made with the high quality of die casting steel (almost 1/8" thick) coated with zinc for rusting and corrosion resistance. Each fastener measures 1-3/16" x 5/8" x 12 gauge (~1/8") thick.
BEST SELLERS
Menu
-
B2B
-
Shopping Agent
-
Forwarding
-
Support
-
Brand Introduction
-
Login
Sign Out
-
Language English
-
Currency RUB
Language
Currency
Drag the image here, or
Click to upload
Tips: Only jpg, jpeg, png, webp
Scan the QR code and use your phone to take a direct photo search.
×
