A: Too much filter added or the mouth is too dirty. Please pour out the excess filter, clean the burner and poke the mouth of the burner thoroughly with a small needle.
Q: Why is there no reaction when the machine is turned on?
A: The fuse is broken, please replace it with a new one.
Q: What if the polished acrylic has bubbles or is not bright?
A: That's because acrylic is not clean, please clean the acrylic material.
Q: What if the pressure is insufficient?
A: Because of air leakage or current value is too small. You can start with a soapy water from the tip of the gun and look for leaks. Or replace the electrolyte.
Q: There is current but no gas, what is going on?
A: It may be that the polishing machine is leaking or the pressure gauge is damaged. You can check the leak or replace the pressure gauge
1. Make electrolytic solution
Add electrolytic powder(sodium hydroxide or NaOH) and water in a plastic basin or glass and ceramic basin, stir them, and then cool for 10 minutes.
Electrolytic solution ratio: 15%
Notice: metal basin is forbidden
Warning: Sodium hydroxide belongs to strong alkali, so its solution is very corrosive once the solution touches clothes or skin, please clean it using water repeatedly
2. Add electrolytic solution and filter solution
Unscrew the inlet nut. Put the funnel to avoid spattering. Add electrolytic solution into the electrolytic cells.
Electrolytic solution must be lower than "normal waterline", and must be higher than "feeding waterline". Then tighten the inlet nut.
Disassemble the filter cup anticlockwise. Add alcohol to the cup lower than 1/3 of the cup.
Assemble the filter cup to the machine and tighten it
Note: the filter solution is distilled water or alcohol which adjusts flame pureness and temperature.
3. Power on test
Check techdata label on the back of machine shell. We produce acrylic flame polisher with 110V and 220V power supply voltage. Power supply voltage and the voltage machine needs must be matchable to avoid damage to the machine.
The plug must have the earth wire to avoid electricshock
The hose connects flame toch and gasoutput. Choose suitable copper nozzles accordingto your requirements.
Power on, if both light and fan works, themachine is working well
4. Pressure test
Close the flame torch, and gas pressure will become higher and higher. When it reaches its limit, current value will become zero, and machine will stop work.
Then lift the pressure-releasing valve, there will be gas releasing. In that case, the machine works well.
Working pressure range is from 0. 13 Mpa to o. 15 Mpa. If pressure reaches to 0. 15 Mpa, machine will stop working,while if pressure becomes 0. 13 Mpa, machine will work again automatically. In that case, machine works well.
A: Too much filter added or the mouth is too dirty. Please pour out the excess filter, clean the burner and poke the mouth of the burner thoroughly with a small needle.
Q: Why is there no reaction when the machine is turned on?
A: The fuse is broken, please replace it with a new one.
Q: What if the polished acrylic has bubbles or is not bright?
A: That's because acrylic is not clean, please clean the acrylic material.
Q: What if the pressure is insufficient?
A: Because of air leakage or current value is too small. You can start with a soapy water from the tip of the gun and look for leaks. Or replace the electrolyte.
Q: There is current but no gas, what is going on?
A: It may be that the polishing machine is leaking or the pressure gauge is damaged. You can check the leak or replace the pressure gauge
1. Make electrolytic solution
Add electrolytic powder(sodium hydroxide or NaOH) and water in a plastic basin or glass and ceramic basin, stir them, and then cool for 10 minutes.
Electrolytic solution ratio: 15%
Notice: metal basin is forbidden
Warning: Sodium hydroxide belongs to strong alkali, so its solution is very corrosive once the solution touches clothes or skin, please clean it using water repeatedly
2. Add electrolytic solution and filter solution
Unscrew the inlet nut. Put the funnel to avoid spattering. Add electrolytic solution into the electrolytic cells.
Electrolytic solution must be lower than "normal waterline", and must be higher than "feeding waterline". Then tighten the inlet nut.
Disassemble the filter cup anticlockwise. Add alcohol to the cup lower than 1/3 of the cup.
Assemble the filter cup to the machine and tighten it
Note: the filter solution is distilled water or alcohol which adjusts flame pureness and temperature.
3. Power on test
Check techdata label on the back of machine shell. We produce acrylic flame polisher with 110V and 220V power supply voltage. Power supply voltage and the voltage machine needs must be matchable to avoid damage to the machine.
The plug must have the earth wire to avoid electricshock
The hose connects flame toch and gasoutput. Choose suitable copper nozzles accordingto your requirements.
Power on, if both light and fan works, themachine is working well
4. Pressure test
Close the flame torch, and gas pressure will become higher and higher. When it reaches its limit, current value will become zero, and machine will stop work.
Then lift the pressure-releasing valve, there will be gas releasing. In that case, the machine works well.
Working pressure range is from 0. 13 Mpa to o. 15 Mpa. If pressure reaches to 0. 15 Mpa, machine will stop working,while if pressure becomes 0. 13 Mpa, machine will work again automatically. In that case, machine works well.
Liquid,cream or cosmetics items are quantity limited in shopping agent service
Chinese medicine is limited to ship by Chinese exporting goods.
2 Limitation for different shipping methods:
3 Yoybuy Product's Label:
Sensitive Product(SEN)
Product With battery
Cream
Powder
Dangerous Products
4 Volume weight Requested:
volume weight=length*height*Width/5000
one side must be less than 120cm,otherwise there is additional fee;250cm products can not be accept;
Any side must be less than 60cm,otherwise you will be charged the greater one between real weight and volume weight,more than 120cm will be not accepted.