YG-1 E2030 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.3125" Overall Length, 0.34375" Cutting Diameter, 0.375" Shank Diameter
YG-1 E2030 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.3125" Overall Length, 0.34375" Cutting Diameter, 0.375" Shank Diameter
  • Center-cutting design allows the end mill to plunge into material like a drill bit for applications such as slotting, drilling, and pocketing on a range of materials
  • Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material
  • Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel
  • Uncoated (bright) tools have no additional surface treatment or coating for use on a range of materials
  • Square nose end mills (also called square end) create sharp, unrounded cuts
Retail Price: $ 8.22
Wholesale Price: Inquire Now
...
YG-1 E2030 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.3125" Overall Length, 0.34375" Cutting Diameter, 0.375" Shank Diameter
YG-1 E2030 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.3125" Overall Length, 0.34375" Cutting Diameter, 0.375" Shank Diameter

BEST SELLERS

...
The YG-1 E2030 uncoated cobalt steel square nose end mill has two flutes, a center-cutting design, and a 30-degree helix angle for general-purpose machining and plunge milling on a range of materials. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit for applications such as slotting, drilling, and pocketing. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The tool’s square end creates sharp, unrounded cuts. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action.

The YG-1 E2030 uncoated cobalt steel square nose end mill has two flutes, a center-cutting design, and a 30-degree helix angle for general-purpose machining and plunge milling on a range of materials. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit for applications such as slotting, drilling, and pocketing. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The tool’s square end creates sharp, unrounded cuts. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action.

Cobalt steel can be run at faster speeds and stays sharp longer than high-speed steel tools, while offering resistance to heat and abrasion. With no coating or surface treatment, this uncoated tool can be used on a range of materials. Cutting diameter tolerance is + 0.0010 to - 0.0000" for end mills with a different shank and cutting diameter and + 0.0015 to - 0.0000" for end mills with the same shank and cutting diameter. This tool has a Weldon shank.

End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.

YG-1 manufactures drills, taps, end mills, and rotary tooling. The company, founded in 1981, is headquartered in South Korea and has a U.S. office in Vernon Hills, IL.

Shipping Notices:
1 Contraband and limited items:
Clgarette,Alcohol,Contraband ?Do not accept
... ... ...
Liquid,cream or cosmetics items are quantity limited in shopping agent service
... ... ...
Chinese medicine is limited to ship by Chinese exporting goods.
...
2 Limitation for different shipping methods:
...
3 Yoybuy Product's Label:
...
Sensitive Product(SEN)
...
Product With battery
...
Cream
...
Powder
...
Dangerous Products
...
....
4 Volume weight Requested:
...
volume weight=length*height*Width/5000
...
one side must be less than 120cm,otherwise there is additional fee;250cm products can not be accept;
...
...
...
...
...
Any side must be less than 60cm,otherwise you will be charged the greater one between real weight and volume weight,more than 120cm will be not accepted.
After Sale Service:
2 The rules apply and summit for receive compensation
3 The conditions of accrual for amount insurance
3 The conditions of accrual for amount insurance
5 Damage to the parcel during international shipping, which resulted in damage to the goods in it
6 Loss of individual goods under international shipment The absence individual goods in the parcel
7 Non-compliance individual goods in color, size, complications Damage to the goods during international shipment
...

BEST SELLERS

Inquire Now
X

Contact us now

Language

Currency

    Upload image to find the same item

    Drag the image here, or Click to upload Tips: Only jpg, jpeg, png, webp

    Scan the QR code and use your phone to take a direct photo search.

    ×