EVIL ENERGY 4AN 1/4" Nylon Stainless Steel Braided CPE Fuel Line Fittings Kit 16Ft(5.6mm ID)

[]

Retail Price: $ 53.99

EVIL ENERGY is our brand,we're a direct and professional manufaturer,one of greatest manufacturer and exporter in Tuning parts include intake system,exhaust system,engine system,cooling system,interior&exterior parts. Accept customized order with minimum quantity.

Hose Material: Nylon Braided + CPE Synthetic Rubber .

The fitting made of T6061 Aluminum,high strength and good durability.

Package quantity : 1pc 16Ft Nylon Braided oil hose + 10pcs 4AN hose fitting

Q&A from other customer :

Can i cut the hose?

1. Yes although you should use the proper technique and or cutting tool.

2. Yes you can. A cut off wheel is what I found to be easiest. It will make the cleanest ends allowing for easier install of fitting. But you can use cutters also

3. yes, i had trouble with the outer layer fraying but it is still functioning and sealed fine

4. Wrap with tape before cutting

Will this work with E85 ? we suggest to choose Teflon hose for E85 oil .

Professional Installer is Highly Recommended !!!!!

Adjustable AN wrench is highly recommended.

Read the detail descriptions Below before purchase !!!!


	Fuel Filter	Swivel Hose End Fitting	Hose Reducer Fitting	Adjustable Wrench	EFI Fitting	16Ft PTFE E85 Fuel Line Kit

Installation Step 1

Mark desired length of hose by wrapping it in tape. Using a fine tooth hacksaw or cut off wheel cut hrough hose at the specified length. Once finished ,remove tape and clean away any debris from inside of hose.

Installation Step 2

Hold or clamp socket in place with soft vise jaws and insert hose by turning hose clockwise. Turn hose clockwise until hose is snug against the back of socket threads.
Mark hose with tape or marker at rear of socket .This will later show you if the hose has pushed out of the socket during assembly, and if so ,may leak when used.

Installation Step 3

Liberally apply assembly lube to nipple before placing nipple into soft vise jaws and turning socket onto nipple threads.

Installation Step 4

Start threading socket over the nipple by hand .Continue to tighten by hand as far as possible . Using our adjustable wrench, continue to turning socket onto nipple threads until the base of socket is within.

NOTE: After installation, wash and then test assembly for an interval of 30to 60 seconds using twice then maximum operating pressure.

Application of 16Ft Fuel Hose Line and 4AN Swivel Hose End Fitting

This website follows the safe harbor principle. If any infringement, please inform us in time and we will delete it in time. About safe harbor，please click here to learn more.

After Sale Service:

1 Insurance Policy: Click to go to the Help Center to view the Insurance Policy

2 The rules apply and summit for receive compensation

3 The conditions of accrual for amount insurance

5 Damage to the parcel during international shipping, which resulted in damage to the goods in it

6 Loss of individual goods under international shipment The absence individual goods in the parcel

7 Non-compliance individual goods in color, size, complications Damage to the goods during international shipment

8 Returns Policy: Click to go to the Help Center to view the Returns Policy

All Category
All Category

Women's Clothings

Men's Clothings

EVIL ENERGY 4AN 1/4" Nylon Stainless Steel Braided CPE Fuel Line Fittings Kit 16Ft(5.6mm ID)

BEST SELLERS

Product introduction

Shipping Notices

Product Description

Hose Material: Nylon Braided + CPE Synthetic Rubber .

The fitting made of T6061 Aluminum,high strength and good durability.

Package quantity : 1pc 16Ft Nylon Braided oil hose + 10pcs 4AN hose fitting

Q&A from other customer :

Can i cut the hose?

1. Yes although you should use the proper technique and or cutting tool.

2. Yes you can. A cut off wheel is what I found to be easiest. It will make the cleanest ends allowing for easier install of fitting. But you can use cutters also

3. yes, i had trouble with the outer layer fraying but it is still functioning and sealed fine

4. Wrap with tape before cutting

Will this work with E85 ? we suggest to choose Teflon hose for E85 oil .

Professional Installer is Highly Recommended !!!!!

Adjustable AN wrench is highly recommended.

Read the detail descriptions Below before purchase !!!!


	Fuel Filter	Swivel Hose End Fitting	Hose Reducer Fitting	Adjustable Wrench	EFI Fitting	16Ft PTFE E85 Fuel Line Kit

Installation Step 1

Installation Step 2

Hold or clamp socket in place with soft vise jaws and insert hose by turning hose clockwise. Turn hose clockwise until hose is snug against the back of socket threads.
Mark hose with tape or marker at rear of socket .This will later show you if the hose has pushed out of the socket during assembly, and if so ,may leak when used.

Installation Step 3

Liberally apply assembly lube to nipple before placing nipple into soft vise jaws and turning socket onto nipple threads.

Installation Step 4

NOTE: After installation, wash and then test assembly for an interval of 30to 60 seconds using twice then maximum operating pressure.

Application of 16Ft Fuel Hose Line and 4AN Swivel Hose End Fitting

Shipping Notices:

1 Contraband and limited items:

Clgarette,Alcohol,Contraband ?Do not accept

Liquid,cream or cosmetics items are quantity limited in shopping agent service

Chinese medicine is limited to ship by Chinese exporting goods.

2 Limitation for different shipping methods:

3 Yoybuy Product's Label:

Sensitive Product(SEN)

Product With battery

Cream

Powder

Dangerous Products

4 Volume weight Requested:

volume weight=length*height*Width/5000

one side must be less than 120cm，otherwise there is additional fee；250cm products can not be accept；

Any side must be less than 60cm，otherwise you will be charged the greater one between real weight and volume weight，more than 120cm will be not accepted.