Air Compressor
Model: BT-16
Voltage : 12 volt DC
Adapter: International convertor,100v -240v included
Plugs : US available
Sound : Quiet, vibration free
Holder : Airbrush holder, soft plastic
Port : Easy push-over & pull-off air hose connection
Air hose: 1.5m Air flow: 7.5L/min
Max pressure:25PSI
Time:  Designed for extended running and use
N.W./G.W.: 0.578kg/0.804kg

Suitable for 0.2~0.5mm airbrush ,especially perfect for makeup, cosmetic ,nail painting .
 Please contact support@pinkiou.com if you met any problem while using



 

Compressor Troubleshooting

Most of the not power on problem are related to the reason that Plugin is not fully inserted.
Please find the picture showed on the right.
Do press the plug to make sure that plugin is fully inserted into the slot.


Airbrush Troubleshooting
The majority of airbrush problems are related to the lack of regular thorough cleanings.
o Common mistakes when using an airbrush:
 Not cleaning the airbrush after each application
 Applying too much product
 Holding the airbrush incorrectly when applying
 Moving the airbrush too quickly when applying makeup
 Putting too much product in the cup
 Pulling the trigger all the way back while applying your airbrush
foundation.
 Not keeping the airbrush brush in constant motion (holding it still) will
cause blotchiness
o Troubleshooting Problems and Solutions
 Heavy, Blotchy or Uneven Coverage
 Airflow Setting to High – Lower Airflow setting
 Holding airbrush too close to the face - Stay 6 to 8 inches away
from your face to prevent the makeup from being caked on or
blotchy
 Allowing too much makeup to flow by pulling trigger too far back
– Only pull the trigger about 1/3 to 1/2 way back for a very light
feathered and soft spray. Pulling the trigger past the midpoint can
result in a heavy, blotchy or uneven coverage.
 Airbrush Not Spraying
 Clogged Nozzle – Remove and clean nozzle
 Damaged Nozzle – Remove and replace with new nozzle
 Tip Head is Loose – Tighten Tip Head
 Needle not Moving – Tighten loose needle chucking nut
 Air Pressure to Low – Adjust to higher airflow setting
 Grainy or Textured Spray
 Air Pressure to Low – Adjust to higher airflow setting
 Dried Makeup on End of Needle – Remove, clean and lube needle
 Dirty Airbrush Nozzle – Remove and clean nozzle
 Makeup too thick – Use fresh makeup from a thoroughly shaken
bottle, possibly have applied too much makeup.
 Bubbling Fluid in Cup
 Clogged or Damaged Nozzle – Remove and clean or replace
nozzle
 Tip Head is Loose – Tighten Tip Head
 Spray Cannot be Shutoff
 Clogged or Damaged Nozzle – Remove and clean or replace
nozzle
 Dirty or Stuck Needle – Remove, clean and lube needle
 Needle not seating all the way into the nozzle due to loose needle
chucking nut - Push needle in until it seats in the nozzle, then
tighten needle chucking nut
 Sticky Trigger – Trigger and air valve packing need to be lubed
 Sprays Double Lines or Heavy on One Side
 Split Nozzle Tip – Remove and Replace
 Bent Needle Tip – Remove and straighten or replace
 Nozzle Tip Not Centered in Tip Head – Remove and clean
airbrush tip head threads and head thread assembly on airbrush
 Dried Makeup on End of Needle - Remove and clean needle
 Dirty Airbrush Nozzle – Remove and clean nozzle
 Makeup Blobs at the Beginning of a Stroke
 Spraying makeup before moving your hand – Have your hand in
motion before triggering makeup flow
 Makeup Blobs at the End of a Stroke
 Stopping the airbrush movement before shutting off makeup flow -
Follow through with your airbrush stroke until after the trigger is
released to shutoff makeup flow
 Splattering
Allowing the needle to snap back into the tip – Always release the trigger gently to avoid
splattering