ECCPP Mass Air Flow Sensor 996 606 123 00 Fit For 1999-2001 for Porsche 911 3.4L,1997-1999 for Porsche Boxster 2.5L,2000-2005 for Porsche Boxster 2.7L

FITMENT - Mass Air Flow Sensor for 1999-2001 for Porsche 911 3.4L,1997-1999 for Porsche Boxster 2.5L,2000-2005 for Porsche Boxster 2.7L,2000-2005 for Porsche Boxster 3.2L

PARTS INFORMATION - Before purchase this parts, please check the compatibility information or call your local dealer to verify the correct OEM part number and clean out the air box and replace the air filter before installing the MAF Meter, or the Code and Check Engine Light may keep showing even if you replace a new Mass Air Flow Sensor

STABILITY - Provides more consistent voltage to eliminate engine rough idle problems. OE NUMBERS: 996 606 123 00

FEATURE - The Mass Air Flow (MAF) sensor measures the amount of air flow entering the intake manifold using a heated grid or wire. The PCM uses this signal primarily for fuel control

BENIFITS - Platinum connector threads reduce the number of connection points for faster reaction to change.Before installing the MAF, Please clean the air box and replace the air filter, otherwise \"Code and Check Engine Light\" may always be displayed even if the MAF is replaced.

Retail Price: $ 24.77

Wholesale Price: Inquire Now

FITMENT

1999-2001PORSCHE 911

1998-2004PORSCHE BOXSTER

(More models please check the model table)

Installing The Replacement Mass Air Flow Sensor

1. Position MAF sensor in the vehicle. Make sure the airflow direction indicated on the sensor is toward the engine.

2. Install sensor-to-air-duct seal(s), if so equipped, on the replacement MAF sensor.

3. Connect the MAF sensor to the throttle body air cleaner ducts. If the sensor mounts directly on the throttle body, install and tighten the mounting screws to 10 ft-lb. DO NOT OVERTIGHTEN!

4. Position clamps over the air duct/MAF sensor connections and tighten. Replace the clamps if necessary.

NOTE: For the MAF sensor to work properly, the sensor/air duct connections must be airtight.

5.CAREFULLY plug the harness connector lead into the MAF sensor.


100% resolder of critical components ensures superior electrical connections, no intermittent failures and longer product life	Match original location,non-destructive installation	On-car vehicle validation routines ensure that modules meet all form, fit, durability and performance requirements	100% buyer satisfaction.Accept return and refund to ensure your benefit

This website follows the safe harbor principle. If any infringement, please inform us in time and we will delete it in time. About safe harbor，please click here to learn more.

After Sale Service:

1 Insurance Policy: Click to go to the Help Center to view the Insurance Policy

2 The rules apply and summit for receive compensation

3 The conditions of accrual for amount insurance

5 Damage to the parcel during international shipping, which resulted in damage to the goods in it

6 Loss of individual goods under international shipment The absence individual goods in the parcel

7 Non-compliance individual goods in color, size, complications Damage to the goods during international shipment

8 Returns Policy: Click to go to the Help Center to view the Returns Policy

All Category
All Category

Women's Clothings

Men's Clothings

ECCPP Mass Air Flow Sensor 996 606 123 00 Fit For 1999-2001 for Porsche 911 3.4L,1997-1999 for Porsche Boxster 2.5L,2000-2005 for Porsche Boxster 2.7L

BEST SELLERS

Product introduction

Shipping Notices

Product Description

FITMENT

1999-2001PORSCHE 911

1998-2004PORSCHE BOXSTER

(More models please check the model table)

Installing The Replacement Mass Air Flow Sensor

1. Position MAF sensor in the vehicle. Make sure the airflow direction indicated on the sensor is toward the engine.

2. Install sensor-to-air-duct seal(s), if so equipped, on the replacement MAF sensor.

3. Connect the MAF sensor to the throttle body air cleaner ducts. If the sensor mounts directly on the throttle body, install and tighten the mounting screws to 10 ft-lb. DO NOT OVERTIGHTEN!

4. Position clamps over the air duct/MAF sensor connections and tighten. Replace the clamps if necessary.

NOTE: For the MAF sensor to work properly, the sensor/air duct connections must be airtight.

5.CAREFULLY plug the harness connector lead into the MAF sensor.


100% resolder of critical components ensures superior electrical connections, no intermittent failures and longer product life	Match original location,non-destructive installation	On-car vehicle validation routines ensure that modules meet all form, fit, durability and performance requirements	100% buyer satisfaction.Accept return and refund to ensure your benefit

Shipping Notices:

1 Contraband and limited items:

Clgarette,Alcohol,Contraband ?Do not accept

Liquid,cream or cosmetics items are quantity limited in shopping agent service

Chinese medicine is limited to ship by Chinese exporting goods.

2 Limitation for different shipping methods:

3 Yoybuy Product's Label:

Sensitive Product(SEN)

Product With battery

Cream

Powder

Dangerous Products

4 Volume weight Requested:

volume weight=length*height*Width/5000

one side must be less than 120cm，otherwise there is additional fee；250cm products can not be accept；

Any side must be less than 60cm，otherwise you will be charged the greater one between real weight and volume weight，more than 120cm will be not accepted.