allsun Battery Tester Internal Resistance Meter Battery Voltage Tester Digital Battery Analyzer

1. Digital LCD display, easy to read the measurement result. With backlight, it makes it easy to read in low light areas.

2. It is mainly used to measure battery terminal voltage and internal resistance.

3. Adopt four-wire method which helps to ensure the accuracy of the measured value.

4. It is applicable for measurement of internal resistances of Lithium-ion, nickel-hydroxide, lithium-manganese cells or assembled battery.

5. Battery: 9V battery, 6F22 or equivalent, 1 piece (Not Provided by Seller)

Retail Price: $ 37.8

Wholesale Price: Inquire Now

GENERAL SPECIFICATION

Overrange Indication: only figure " 1 " shown on the display

Negative Polarity Indication: " - " shown on the display automatically

Operating Environment: temperature: 0 ~ +40°C

relative humidity: < 80%

Temperature Coefficient: 0.1 x (specified accuracy)/°C (< 18°C or > 28°C)

Storage Environment: temperature: -10 ~ +45°C

relative humidity: < 85%

Battery: 9V battery, 6F22 or equivalent, 1 piece

Low Battery Indication: " " shown on the display

Size: 150×83×44mm (only mainbody )

Weight: about 315g (including battery)

STRUCTURE

1. Display: 3 1/2-digit LCD, with a max. reading of 1999

2. " " Button

Press this " " button to turn on the backlight. The backlight will turns off automatically about 10 secs later.

3. Function / Range Switch

Used to select desired function and range as well as to turn on or off the meter.

To preserve battery life, set this switch to the " OFF " position when the meter is not in use.

4. " " Button

Press this " " button to hold the present reading on the display, the symbol " " will appear on the display

as an indication. To exit the Data Hold mode, just press this button again. " " disappears.

5. Holster

6. Test Probes

1. Set the range switch to desired range position.

2. Connect the red test probe to the positive terminal of the battery to be measured and the black test probe to the negative terminal of the battery.

3. Read the reading on the display.

4. If the display shows " 1 ", it means that the measured value exceeds the selected range and you should set the range switch to a higher range position.

Note:

1. When the test probes are in open circuit state, the display will show " 1 " as an overrange indication.

2. For measurements in the 200m range, set the range switch in the 200m range position and short the two

test probes, the display will show a reading. This reading must be subtracted from all the measurements

in the 200m range.

1. Set the range switch to desired range position.

2. Connect the test probes across the resistor to be measured.

3. Read the reading on the display.

Note:

1. The resistance is measured by the meter with an AC

signal so that the capacitance value and inductance value of the resistor under test can affect the measurement result.

2. The frequency of the meter's test signal is 1kHz.

3. When the test probes are in open circuit state, the display will show " 1 " as an overrange indication.

4. Before measurement, disconnect all power to the circuit to be tested and discharge all capacitors thoroughly.

5. For measurements in the 200m range, set the range switch in the 200m range position and short the two test probes, the display will show a reading. This reading must be subtracted from all the measurements in the 200m range.

1. Set the range switch to desire V range position.Note: a. The range you select must be higher than the

battery's rated voltage.

b. If the magnitude of the battery's voltage is not known beforehand, set the range switch to the highest range position and then reduce it range by range until satisfactory resolution is obtained.

2. Connect the red test probe to the positive terminal of the battery to be measured and the black test probe to

the negative terminal of the battery.

3. Read the reading on the display. The polarity of red test probe connection will be indicated as well.

Packing List

Battery Resistance Tester x 1pc

English User Manualx 1pc

9V battery,6F22 or equivalent x 1pc

Test Lead x 1 pair

This website follows the safe harbor principle. If any infringement, please inform us in time and we will delete it in time. About safe harbor，please click here to learn more.

After Sale Service:

1 Insurance Policy: Click to go to the Help Center to view the Insurance Policy

2 The rules apply and summit for receive compensation

3 The conditions of accrual for amount insurance

5 Damage to the parcel during international shipping, which resulted in damage to the goods in it

6 Loss of individual goods under international shipment The absence individual goods in the parcel

7 Non-compliance individual goods in color, size, complications Damage to the goods during international shipment

8 Returns Policy: Click to go to the Help Center to view the Returns Policy

All Category
All Category

Women's Clothings

Men's Clothings

allsun Battery Tester Internal Resistance Meter Battery Voltage Tester Digital Battery Analyzer

BEST SELLERS

Product introduction

Shipping Notices

Product Description

GENERAL SPECIFICATION

Overrange Indication: only figure " 1 " shown on the display

Negative Polarity Indication: " - " shown on the display automatically

Operating Environment: temperature: 0 ~ +40°C

relative humidity: < 80%

Temperature Coefficient: 0.1 x (specified accuracy)/°C (< 18°C or > 28°C)

Storage Environment: temperature: -10 ~ +45°C

relative humidity: < 85%

Battery: 9V battery, 6F22 or equivalent, 1 piece

Low Battery Indication: " " shown on the display

Size: 150×83×44mm (only mainbody )

Weight: about 315g (including battery)

STRUCTURE

1. Display: 3 1/2-digit LCD, with a max. reading of 1999

2. " " Button

Press this " " button to turn on the backlight. The backlight will turns off automatically about 10 secs later.

3. Function / Range Switch

Used to select desired function and range as well as to turn on or off the meter.

To preserve battery life, set this switch to the " OFF " position when the meter is not in use.

4. " " Button

Press this " " button to hold the present reading on the display, the symbol " " will appear on the display

as an indication. To exit the Data Hold mode, just press this button again. " " disappears.

5. Holster

6. Test Probes

1. Set the range switch to desired range position.

2. Connect the red test probe to the positive terminal of the battery to be measured and the black test probe to the negative terminal of the battery.

3. Read the reading on the display.

4. If the display shows " 1 ", it means that the measured value exceeds the selected range and you should set the range switch to a higher range position.

Note:

1. When the test probes are in open circuit state, the display will show " 1 " as an overrange indication.

2. For measurements in the 200m range, set the range switch in the 200m range position and short the two

test probes, the display will show a reading. This reading must be subtracted from all the measurements

in the 200m range.

1. Set the range switch to desired range position.

2. Connect the test probes across the resistor to be measured.

3. Read the reading on the display.

Note:

1. The resistance is measured by the meter with an AC

signal so that the capacitance value and inductance value of the resistor under test can affect the measurement result.

2. The frequency of the meter's test signal is 1kHz.

3. When the test probes are in open circuit state, the display will show " 1 " as an overrange indication.

4. Before measurement, disconnect all power to the circuit to be tested and discharge all capacitors thoroughly.

1. Set the range switch to desire V range position.Note: a. The range you select must be higher than the

battery's rated voltage.

b. If the magnitude of the battery's voltage is not known beforehand, set the range switch to the highest range position and then reduce it range by range until satisfactory resolution is obtained.

2. Connect the red test probe to the positive terminal of the battery to be measured and the black test probe to

the negative terminal of the battery.

3. Read the reading on the display. The polarity of red test probe connection will be indicated as well.

Packing List

Battery Resistance Tester x 1pc

English User Manualx 1pc

9V battery,6F22 or equivalent x 1pc

Test Lead x 1 pair

Shipping Notices:

1 Contraband and limited items:

Clgarette,Alcohol,Contraband ?Do not accept

Liquid,cream or cosmetics items are quantity limited in shopping agent service

Chinese medicine is limited to ship by Chinese exporting goods.

2 Limitation for different shipping methods:

3 Yoybuy Product's Label:

Sensitive Product(SEN)

Product With battery

Cream

Powder

Dangerous Products

4 Volume weight Requested:

volume weight=length*height*Width/5000

one side must be less than 120cm，otherwise there is additional fee；250cm products can not be accept；

Any side must be less than 60cm，otherwise you will be charged the greater one between real weight and volume weight，more than 120cm will be not accepted.

After Sale Service:

1 Insurance Policy: Click to go to the Help Center to view the Insurance Policy

2 The rules apply and summit for receive compensation

3 The conditions of accrual for amount insurance

5 Damage to the parcel during international shipping, which resulted in damage to the goods in it

6 Loss of individual goods under international shipment The absence individual goods in the parcel

7 Non-compliance individual goods in color, size, complications Damage to the goods during international shipment

8 Returns Policy: Click to go to the Help Center to view the Returns Policy