GVKVGIH is a young brand which mainly specialize in dual sim card adapter for smartphone, opensource hardware, electronic components and different kinds of DIY tools and kits.
Any different compare to the original?
The only difference is it will make the 1X function unclickable when you open the camera》Photo,but you still own the zoom function
Package included:
1 x Brand New OEM Back Rear Camera module for iPhone 7Plus
1 x Clean Wiper with "GVKVGIH" LOGO
A pack of open tool kit for iPhone(6 piece)
1 x Upgraded screwdriver with 5 pieces screwdriver head
Kindly Noted:(Important!!)
1.Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
2.Power off your iPhone before beginning disassembly
How to Replace Your Broken Back Camera
1,Power off your iPhone. Remove the two Pentalobe screws, located at the bottom of the iPhone, next to the lightning connector.
2,Use a Heat Gun or Hair Dryer, to apply mild heat to the lower edge of the iPhone, for approx. one minute.
3,Apply a suction cup to the lower left corner of the display assembly.Pull up on the suction cup with firm, constant pressure, to create a slight gap between the front panel and rear case.Place the flat edge of a spudger into the gap between the screen and rear case, directly above the headphone jack, and twist the spudger to widen the gap.Slide the spudger up the side of the phone to separate the adhesive and free the clips
4,Pull up on the suction cup to lift up the display and open the iPhone.Slide an opening pick underneath the display along the top edge of the phone to loosen the last of the adhesive.
5,Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.Open the iPhone by swinging the display up from the left side, like the back cover of a book.
6,Remove the following tri-point Y000 screws securing the lower display cable bracket to the logic board.Remove the bracket.
7,Use the point of a spudger to lift the battery connector out of its socket on the logic board.
8,Use the flat end of a spudger or a to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.
9,Remove the tri-point Y000 screws securing the bracket over the front panel sensor assembly connector.Remove the bracket.
10,Disconnect the front panel sensor assembly connector from its socket on the logic board.Remove the display assembly
11,Remove the two screws securing the rear-facing camera bracket:
12,Remove the bracket.
13,Disconnect the two camera cable connectors by prying them straight up from their sockets.
14,Use the flat end of a spudger to pry up the rear-facing camera assembly from the top edge of the iPhone.
15,Remove the Back Camera assembly.Congratulations! You have now successfully removed your Back Camera!To reinstall the iPhone, use the previous steps in this manual and apply them backwards.
Who Need It?
When your iPhone 7P back rear camera is facing below issue cracked/broken/unclear or not working, the new OEM back rear camera can solve the problem, makes your iPhone 7P works like original new.
GVKVGIH is a young brand which mainly specialize in dual sim card adapter for smartphone, opensource hardware, electronic components and different kinds of DIY tools and kits.
Any different compare to the original?
The only difference is it will make the 1X function unclickable when you open the camera》Photo,but you still own the zoom function
Package included:
1 x Brand New OEM Back Rear Camera module for iPhone 7Plus
1 x Clean Wiper with "GVKVGIH" LOGO
A pack of open tool kit for iPhone(6 piece)
1 x Upgraded screwdriver with 5 pieces screwdriver head
Kindly Noted:(Important!!)
1.Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
2.Power off your iPhone before beginning disassembly
How to Replace Your Broken Back Camera
1,Power off your iPhone. Remove the two Pentalobe screws, located at the bottom of the iPhone, next to the lightning connector.
2,Use a Heat Gun or Hair Dryer, to apply mild heat to the lower edge of the iPhone, for approx. one minute.
3,Apply a suction cup to the lower left corner of the display assembly.Pull up on the suction cup with firm, constant pressure, to create a slight gap between the front panel and rear case.Place the flat edge of a spudger into the gap between the screen and rear case, directly above the headphone jack, and twist the spudger to widen the gap.Slide the spudger up the side of the phone to separate the adhesive and free the clips
4,Pull up on the suction cup to lift up the display and open the iPhone.Slide an opening pick underneath the display along the top edge of the phone to loosen the last of the adhesive.
5,Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.Open the iPhone by swinging the display up from the left side, like the back cover of a book.
6,Remove the following tri-point Y000 screws securing the lower display cable bracket to the logic board.Remove the bracket.
7,Use the point of a spudger to lift the battery connector out of its socket on the logic board.
8,Use the flat end of a spudger or a to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.
9,Remove the tri-point Y000 screws securing the bracket over the front panel sensor assembly connector.Remove the bracket.
10,Disconnect the front panel sensor assembly connector from its socket on the logic board.Remove the display assembly
11,Remove the two screws securing the rear-facing camera bracket:
12,Remove the bracket.
13,Disconnect the two camera cable connectors by prying them straight up from their sockets.
14,Use the flat end of a spudger to pry up the rear-facing camera assembly from the top edge of the iPhone.
15,Remove the Back Camera assembly.Congratulations! You have now successfully removed your Back Camera!To reinstall the iPhone, use the previous steps in this manual and apply them backwards.
Who Need It?
When your iPhone 7P back rear camera is facing below issue cracked/broken/unclear or not working, the new OEM back rear camera can solve the problem, makes your iPhone 7P works like original new.
Liquid,cream or cosmetics items are quantity limited in shopping agent service
Chinese medicine is limited to ship by Chinese exporting goods.
2 Limitation for different shipping methods:
3 Yoybuy Product's Label:
Sensitive Product(SEN)
Product With battery
Cream
Powder
Dangerous Products
4 Volume weight Requested:
volume weight=length*height*Width/5000
one side must be less than 120cm,otherwise there is additional fee;250cm products can not be accept;
Any side must be less than 60cm,otherwise you will be charged the greater one between real weight and volume weight,more than 120cm will be not accepted.