Bobbin Style Class15 L M Size for Sewing Juki Brother Singer Long-Arm Quilting Embroidery Machine
Leaving the nuts on the thread guide rods, attach it to the metal plate.
Only screw in deep enough to be flush with the table top surface. Screwing in too deep will cause the unit to rest unevenly. To tighten, secure the nut.
Place bobbin on winder making sure bobbin is fully seated and pressed fully downward. Leave a few inch tail. Create a small amount of slack in the thread line between the tension disks and bobbin (approximately to the edge of the machine or slightly more). While holding the tail and leaving the slack, press the start button. Once 10 or more revolutions of the bobbin have started and secured winding, stop the machine. Trim the tail being held at the bobbin. Press start and resume winding.
Machine will automatically shut off when bobbin is full based off of where you have adjusted the inductor at the end of the unit.
Guide through thread guide rod, down and into small hole on the side of tension disks. Guide thread clockwise between tension disks and wrap clockwise twice before inserting thread end into hole in bobbin.
Place a bobbin on the winder. Loosen the screw on the inductor and move it inward approximately 1/8”in from the outer edge of the bobbin. Secure screw. Adjust as needed if screws are not full enough or too full. Factory default is for bobbin diameter 2.03cm. (Class15/A-and L style Bobbin)
Press start and resume winding.
Machine will automatically shut off when bobbin is full based off of where you have adjusted the inductor at the end of the unit.
Automatic bobbin winder machine with thread cutter
Automatic bobbin winder machine with thread cutter
When bobbin automatically stops winding, use the thread cutter located in the center of unit located by the start button.
Electric bobbin winder
Electric bobbin winder does not include thread & bobbin
Factory default is for bobbin wide 8.89mm (L-style Bobbin). It can be even winding for bobbin wide 11.7 and 10.7mm by turning the tension knob anti-clock about 7 circles.
Bobbin Style Class15 L M Size for Sewing Juki Brother Singer Long-Arm Quilting Embroidery Machine
Leaving the nuts on the thread guide rods, attach it to the metal plate.
Only screw in deep enough to be flush with the table top surface. Screwing in too deep will cause the unit to rest unevenly. To tighten, secure the nut.
Place bobbin on winder making sure bobbin is fully seated and pressed fully downward. Leave a few inch tail. Create a small amount of slack in the thread line between the tension disks and bobbin (approximately to the edge of the machine or slightly more). While holding the tail and leaving the slack, press the start button. Once 10 or more revolutions of the bobbin have started and secured winding, stop the machine. Trim the tail being held at the bobbin. Press start and resume winding.
Machine will automatically shut off when bobbin is full based off of where you have adjusted the inductor at the end of the unit.
Guide through thread guide rod, down and into small hole on the side of tension disks. Guide thread clockwise between tension disks and wrap clockwise twice before inserting thread end into hole in bobbin.
Place a bobbin on the winder. Loosen the screw on the inductor and move it inward approximately 1/8”in from the outer edge of the bobbin. Secure screw. Adjust as needed if screws are not full enough or too full. Factory default is for bobbin diameter 2.03cm. (Class15/A-and L style Bobbin)
Press start and resume winding.
Machine will automatically shut off when bobbin is full based off of where you have adjusted the inductor at the end of the unit.
Automatic bobbin winder machine with thread cutter
Automatic bobbin winder machine with thread cutter
When bobbin automatically stops winding, use the thread cutter located in the center of unit located by the start button.
Electric bobbin winder
Electric bobbin winder does not include thread & bobbin
Factory default is for bobbin wide 8.89mm (L-style Bobbin). It can be even winding for bobbin wide 11.7 and 10.7mm by turning the tension knob anti-clock about 7 circles.
Liquid,cream or cosmetics items are quantity limited in shopping agent service
Chinese medicine is limited to ship by Chinese exporting goods.
2 Limitation for different shipping methods:
3 Yoybuy Product's Label:
Sensitive Product(SEN)
Product With battery
Cream
Powder
Dangerous Products
4 Volume weight Requested:
volume weight=length*height*Width/5000
one side must be less than 120cm,otherwise there is additional fee;250cm products can not be accept;
Any side must be less than 60cm,otherwise you will be charged the greater one between real weight and volume weight,more than 120cm will be not accepted.