Press and hold the “-” button for 4-6 seconds to Turn ON/OFF the TPMS monitor

1. Press and hold the “-” button for 4-6 seconds to Turn ON the TPMS monitor.

2. Install the 6 sensors after the monitor is ON, the sensors will take seconds to be registered and connected to the TPMS LCD monitor.

3. Important Notice: Install the 6 sensors after the monitor is ON if not, the TPMS monitor and TPMS sensors will not be signal “Paired or Connected”.

4.Please check the videos for the operation of this truck RV trailar TPMS under this TPMS page

High pressure/Low pressure/High temperature Alarm Value can be set by your need

This TPMS Pressure Range: 0-199 PSI

Default High pressure alarm : 116 PSI

Default Low pressure alarm : 60 PSI

Default High temperature alarm:149 °F

which means the TPMS Monitor will alarm if the tire pressure lower than 60 PSI or higher than 116 PSI, or tire temperature higher than 149 °F.

But do remember that High pressure/Low pressure/High temperature Alarm Value can be set by your need

We will need to set the minimum and maximum pressures (there is an alarm that goes off when you reach those limits) for rear 4 tires and front 2 tires .

How to set tire pressure alarm level for front 2 tires

For example, we want front 2 tires 55-120PSI

Set the minimum alarm pressures from 60 to 55PSI for front 2 tires:1. first turn on the monitor, next press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”. 2. And then Press "-" for 7 times, screen shows "LO 60" (beside the front 2 tires), press the "SET" for 1 time, the Arabic numerals 60 flickers, press "-" for 5 times to turn down the Arabic numerals to 55, press "SET" for 1 time to finish. 3.Hold "SET" for a few seconds to save the change

Set the maximum alarm pressures from 116 to 120PSI for front 2 tires: first turn on the monitor, next press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”. And then Press "-" for 8 times, screen shows "HI 116" (beside the front 2 tires), press the "SET" for 1 time, the Arabic numerals 116 flickers, press "+" for 4 times to turn down the Arabic numerals to 120, press "SET" for 1 time to finish. Hold "SET" for a few seconds to save the change

How to set tire pressure alarm level for rear 4 tires

For example, we want rear 4 tires 50-125PSI

Set the minimum alarm pressures from 60 to 50PSI for rear 4 tires:

1. First turn on the monitor, next press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”. 2. And then Press "-" for 5 times, screen shows "LO 60" (beside the rear 4 tires), press the " SET " for one time, the Arabic numerals 60 flickers, 3. Press "-" for 10 times to turn down the Arabic numerals to 50, press " SET " for one time to finish. 4. Hold "SET" for a few seconds to save the change

Set the maximum alarm pressures from 116 to 125PSI for rear 4 tires: first turn on the monitor, next press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”. And then Press "-" for 6 times, screen shows "HI 116" (beside the rear 4 tires), press the " SET " for 1 time, the Arabic numerals 116 flickers, press "+" for 9 times to turn down the Arabic numerals to 125, press " SET " for 1 time to finish. Hold "SET" for a few seconds to save the change

How to set the tire temperature and pressure unit

Set the tire temperature from Celsius to Fahrenheit

1. Turn on the monitor, press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”.

2. Press "+" for 1 time, "℃℉" shows on the screen, press "SET" button for one time, click "+" or"-" until "℉" flashes on the screen, press "SET" button for 1 time to finish. Hold "SET" button for a few seconds to save the change

Switch pressure unit from BAR to PSI

1. Turn on the monitor, press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”.

2. Press "SET" button for 1 time, click "+" or"-" until "PSI" flashes on the screen, press "SET" for 1 time to finish. Hold "SET" button for a few seconds to save the change

How do we change from 6-tire mode to 4-tire mode

Default is 6 tires mode

1. Turn on the monitor, press and hold "+" button for 4-6 seconds until the screen shows “BAR PSI”.

2. Press "-" button for 1 time, right-down corner shows "6", which means 6-tire mode is on.

3. Press "SET" button for 1 time, the 6 tire image flashes.

4. Press "-" or "+"button, 6-tire-image changes to 4-tire-image, right-down corner shows "4"

5. Press "SET" button for 1 time, it is now 4-tire mode, vice versa.

6. Hold "SET" button for a few seconds to save the change