- ['The updated Crossfire red dot is a no-nonsense sight for near any application, and when your rifle, shotgun, or rimfire needs a simple point of aim and none of the frills, the Crossfire should be at the top of your list.', 'With up to a 50, 000 hour battery life and night-vision compatibility at the lowest two settings, the sight will keep working in a variety of conditions. The low and skeletonized lower 1/3 co-witness mounts provide vesatility for this lightweight optic.', 'The 2 MOA dot is quick to acquire in close-quarters, while remaining fine enough to promote pin-point accuracy at extended range. 11 illumination settings allows shooters to change the dot intensity to the situation at hand.', 'Increased light transmission with multiple anti-reflective coatings on all air-to-glass surfaces. Unlimited eye relief for rapid target acquisition.', 'Highly durable hard-coat anodization provides a low-glare matte surface and helps camouflage position. O-ring seals prevent moisture, dust and debris from penetrating for reliable waterproof performance', 'Included Components: Crossfire Red Dot (Led Upgrade)']
When your rifle, shotgun or rimfire just needs a simple point of aim and none of the frills, the Crossfire should be at the top of your list. The 2 MOA dot is quick to acquire in close-quarters scenarios, while remaining fine enough to promote pin-point accuracy at extended range. In addition to looking awesome, the included skeletonized lower 1/3 co-witness mount provides a rock-solid and extremely lightweight platform for your red dot. The Crossfire is a no-nonsense sight for near any application.
2 MOA Dot Reticle
The daylight bright red dot is easy to see and paints targets regardless of lighting conditions or background.
The key thing to remember when shooting with the Crossfire Red Dot is to keep both of your eyes open! Shooting with both eyes open allows you to take full advantage of your peripheral vision to get on target very quickly. Eye placement is not critical.
Windage and Elevation Adjustments
The Crossfire Red Dot incorporates elevation and windage dials with audible clicks. Each small click will move the point-of-impact one Minute of Angle. 1 MOA will closely correspond to one inch at 100 yards, 1/2 inch at 50 yards, 1/4 inch at 25 yards, etc.
Remove the turret cap and use the raised bar on the cover or a coin to turn the adjustment dial. Move the dials in the direction you wish the bullet’s point-of-impact to change. Turning the elevation turret counter-clockwise will raise the elevation. Turning the windage turret clockwise will move the point of impact to the left.
Mounting the Crossfire Red Dot
The Crossfire Red Dot can be mounted on a variety of platforms using the high mount or low mount.
- Attach the unit to the rail/base with the illumination dial positioned on the right side.
- Make sure the mount is solidly seated in the base groove. In order to prevent recoil injury, position the Red Dot so you have at least four inches of eye relief.
- Be sure the base clamp is hooked around the outside of the rail/base.
- Press the Red Dot downward and forward toward the muzzle. Then, firmly tighten the base clamp bolt using the hex wrench.
BEST SELLERS
From the manufacturer
When your rifle, shotgun or rimfire just needs a simple point of aim and none of the frills, the Crossfire should be at the top of your list. The 2 MOA dot is quick to acquire in close-quarters scenarios, while remaining fine enough to promote pin-point accuracy at extended range. In addition to looking awesome, the included skeletonized lower 1/3 co-witness mount provides a rock-solid and extremely lightweight platform for your red dot. The Crossfire is a no-nonsense sight for near any application.
2 MOA Dot Reticle
The daylight bright red dot is easy to see and paints targets regardless of lighting conditions or background.
The key thing to remember when shooting with the Crossfire Red Dot is to keep both of your eyes open! Shooting with both eyes open allows you to take full advantage of your peripheral vision to get on target very quickly. Eye placement is not critical.
Windage and Elevation Adjustments
The Crossfire Red Dot incorporates elevation and windage dials with audible clicks. Each small click will move the point-of-impact one Minute of Angle. 1 MOA will closely correspond to one inch at 100 yards, 1/2 inch at 50 yards, 1/4 inch at 25 yards, etc.
Remove the turret cap and use the raised bar on the cover or a coin to turn the adjustment dial. Move the dials in the direction you wish the bullet’s point-of-impact to change. Turning the elevation turret counter-clockwise will raise the elevation. Turning the windage turret clockwise will move the point of impact to the left.
Mounting the Crossfire Red Dot
The Crossfire Red Dot can be mounted on a variety of platforms using the high mount or low mount.
- Attach the unit to the rail/base with the illumination dial positioned on the right side.
- Make sure the mount is solidly seated in the base groove. In order to prevent recoil injury, position the Red Dot so you have at least four inches of eye relief.
- Be sure the base clamp is hooked around the outside of the rail/base.
- Press the Red Dot downward and forward toward the muzzle. Then, firmly tighten the base clamp bolt using the hex wrench.
BEST SELLERS
Menu
-
B2B
-
Shopping Agent
-
Forwarding
-
Support
-
Brand Introduction
-
Login
Sign Out
-
Language English
-
Currency RUB
Language
Currency
Drag the image here, or
Click to upload
Tips: Only jpg, jpeg, png, webp
Scan the QR code and use your phone to take a direct photo search.
×
