PC-Concrete Two-Part Epoxy Adhesive Paste for Anchoring and Crack Repair
PC Concrete epoxy gel is an anchoring and concrete repair product. PC Concrete is formulated for anchoring threaded rods, bolts, rebar dowels and smooth dowels into concrete, grout filled block, and unreinforced masonry. PC Concrete has exceptional strength, maximum field reliability, along with a high heat deflection temperature of 134°F, which provides engineers and contractors with a choice for specifying and setting adhesive anchors in elevated temperature environments. PC Concrete is excellent for filling and repair cracks in concrete.
Features
Long Working TimeLong working time (20 minutes at 75°F) Always be sure the hole/crack is prepared in advance before starting. If at all possible, schedule dispensing to consume an entire cartridge at one time with no interruption of epoxy flow. |
Fill and Repair CracksExcellent for filling and repair cracks in concrete. PC Concrete out performs all caulks and hydraulic cement. PC Concrete will not come loose from any cleaned concrete surface. PC Concrete will hold during expansion and contraction of concrete. PC Concrete the best solution for permanent concrete repair. |
Proudly made in the USAAll PC Products are made in the USA and shipped from Allentown, PA. |
|
|
|
|
|
|---|---|---|---|---|
| PC Products PC-Concrete Two-Part Epoxy Adhesive Paste for Anchoring and Crack Repair | PC Products PC-Masonry Two-Part Masonry Repair Epoxy Adhesive Paste | PC Products PC-Xtreme Polyurea Elastomeric Crack and Joint Filler | PC Products PC-Crete Hand Moldable Concrete Epoxy Putty | |
| Color Liquid / Dry | Gray / Gray | Gray / Gray | Gray / Gray | Limestone / Limestone |
| Sandable / Paintable / Machinable | Yes / Yes / Yes | Yes / Yes / Yes | Yes / Yes / Yes | Yes / Yes / Yes |
| Work Time / Service Time (at 70 F) | 20 min / 4 hours | 20 min / 4 hours | 10 min / 1 hour | 3 min / 1 hour |
| Tensile Strength | 6780 psi | 11,000 psi | n/a - filler | 650 psi |
| Can apply to wet surfaces / Waterproof after cure | Yes / Yes | Yes / Yes | Yes / No | Yes / Yes |
| No drip or sag / Fill characteristics | Yes In Smaller Volume / Excellent | Yes / Excellent | No / Good | No / Good |
| Temperature range | -20 - 200° F | -20 - 200° F | -50 - 200° F | -20 - 250° F |
| Permanent repair? | Yes | Yes | Yes | Yes - Emergency |
| Toxicity when cured? | No | No | No - FDA Approved | No |
| Coverage - cubic inch per ounce | 1.5 | 1.5 | 1.7 | 1.5 |
About PC Products
Protective Coating Company was founded and incorporated in 1954 by John (Jack) Long as a service company providing customers with a waterproofing product called 'Spraycrete'. Soon afterward, our signature product PC-7 paste epoxy was developed. This product put Protective Coating Co. on the map. Today, we make a full line of repair and wood restoration products. From wood repairs to concrete repairs and most repairs in between, We have you covered.
Now in its 3rd generation, Protective Coating Co. still maintains their small town philosophy and remains a family run company committed to manufacturing quality products. Every batch of mixed material is still hand tested to insure our high standard of quality. In each of our products you will find more than just a product that performs as intended, you will find a team that stands behind their products. From Concrete to Wood restoration and heavy duty permanent repairs, we have you covered.Yeah; We can fix that!
BEST SELLERS
From the manufacturer
PC-Concrete Two-Part Epoxy Adhesive Paste for Anchoring and Crack Repair
PC Concrete epoxy gel is an anchoring and concrete repair product. PC Concrete is formulated for anchoring threaded rods, bolts, rebar dowels and smooth dowels into concrete, grout filled block, and unreinforced masonry. PC Concrete has exceptional strength, maximum field reliability, along with a high heat deflection temperature of 134°F, which provides engineers and contractors with a choice for specifying and setting adhesive anchors in elevated temperature environments. PC Concrete is excellent for filling and repair cracks in concrete.
Features
Long Working TimeLong working time (20 minutes at 75°F) Always be sure the hole/crack is prepared in advance before starting. If at all possible, schedule dispensing to consume an entire cartridge at one time with no interruption of epoxy flow. |
Fill and Repair CracksExcellent for filling and repair cracks in concrete. PC Concrete out performs all caulks and hydraulic cement. PC Concrete will not come loose from any cleaned concrete surface. PC Concrete will hold during expansion and contraction of concrete. PC Concrete the best solution for permanent concrete repair. |
Proudly made in the USAAll PC Products are made in the USA and shipped from Allentown, PA. |
|
|
|
|
|
|
|---|---|---|---|---|
| PC Products PC-Concrete Two-Part Epoxy Adhesive Paste for Anchoring and Crack Repair | PC Products PC-Masonry Two-Part Masonry Repair Epoxy Adhesive Paste | PC Products PC-Xtreme Polyurea Elastomeric Crack and Joint Filler | PC Products PC-Crete Hand Moldable Concrete Epoxy Putty | |
| Color Liquid / Dry | Gray / Gray | Gray / Gray | Gray / Gray | Limestone / Limestone |
| Sandable / Paintable / Machinable | Yes / Yes / Yes | Yes / Yes / Yes | Yes / Yes / Yes | Yes / Yes / Yes |
| Work Time / Service Time (at 70 F) | 20 min / 4 hours | 20 min / 4 hours | 10 min / 1 hour | 3 min / 1 hour |
| Tensile Strength | 6780 psi | 11,000 psi | n/a - filler | 650 psi |
| Can apply to wet surfaces / Waterproof after cure | Yes / Yes | Yes / Yes | Yes / No | Yes / Yes |
| No drip or sag / Fill characteristics | Yes In Smaller Volume / Excellent | Yes / Excellent | No / Good | No / Good |
| Temperature range | -20 - 200° F | -20 - 200° F | -50 - 200° F | -20 - 250° F |
| Permanent repair? | Yes | Yes | Yes | Yes - Emergency |
| Toxicity when cured? | No | No | No - FDA Approved | No |
| Coverage - cubic inch per ounce | 1.5 | 1.5 | 1.7 | 1.5 |
About PC Products
Protective Coating Company was founded and incorporated in 1954 by John (Jack) Long as a service company providing customers with a waterproofing product called 'Spraycrete'. Soon afterward, our signature product PC-7 paste epoxy was developed. This product put Protective Coating Co. on the map. Today, we make a full line of repair and wood restoration products. From wood repairs to concrete repairs and most repairs in between, We have you covered.
Now in its 3rd generation, Protective Coating Co. still maintains their small town philosophy and remains a family run company committed to manufacturing quality products. Every batch of mixed material is still hand tested to insure our high standard of quality. In each of our products you will find more than just a product that performs as intended, you will find a team that stands behind their products. From Concrete to Wood restoration and heavy duty permanent repairs, we have you covered.Yeah; We can fix that!
BEST SELLERS
Menu
-
B2B
-
Shopping Agent
-
Forwarding
-
Support
-
Brand Introduction
-
Login
Sign Out
-
Language English
-
Currency RUB
Language
Currency
Drag the image here, or
Click to upload
Tips: Only jpg, jpeg, png, webp
Scan the QR code and use your phone to take a direct photo search.
×
